This is the latest recevied telemetry packets stored in our database for station/object SY2DCI-5. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
| Time | Voltage* | Value2* | Value3* | Value4* | Value5* |
|---|---|---|---|---|---|
| 1787563013 | 3.25 VDC | 0 | 0 | 0 | 0 |
| 1787562952 | 3.21 VDC | 0 | 0 | 0 | 0 |
| 1787562636 | 3.21 VDC | 0 | 0 | 0 | 0 |
| 1787562524 | 3.2 VDC | 0 | 0 | 0 | 0 |
| 1787560667 | 3.27 VDC | 0 | 0 | 0 | 0 |
| 1787559930 | 3.3 VDC | 0 | 0 | 0 | 0 |
| 1787548768 | 2.93 VDC | 0 | 0 | 0 | 0 |
| 1787547206 | 2.94 VDC | 0 | 0 | 0 | 0 |
| 1787547085 | 2.95 VDC | 0 | 0 | 0 | 0 |
| 1787495199 | 3.05 VDC | 0 | 0 | 0 | 0 |
| 1787491716 | 3.1 VDC | 0 | 0 | 0 | 0 |
| 1787491236 | 3.11 VDC | 0 | 0 | 0 | 0 |
| 1787491141 | 3.12 VDC | 0 | 0 | 0 | 0 |
| 1787491051 | 3.13 VDC | 0 | 0 | 0 | 0 |
| 1787490795 | 3.11 VDC | 0 | 0 | 0 | 0 |
| 1787484772 | 3.25 VDC | 0 | 0 | 0 | 0 |
| 1787483406 | 3.25 VDC | 0 | 0 | 0 | 0 |
| 1787478805 | 3.38 VDC | 0 | 0 | 0 | 0 |
| 1787477748 | 3.46 VDC | 0 | 0 | 0 | 0 |
*Used Equation Coefficients:
Voltage: 0, 0.01, 0
Value2: 0, 1, 0
Value3: 0, 1, 0
Value4: 0, 1, 0
Value5: 0, 1, 0
- The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
- Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value2 + b * value + c. - The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
- The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
- All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
- A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)