EA2RCF LoRa APRS MAP Backup

My position About Go to MAIN map Powered by EA2RCF Radioclub Foronda ☰

reset

YB1LZ-9 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YB1LZ-9. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	Temp.*	Humidity*	Pressure*
1791461656	33 °C	41 %RH	937 hPa
1791459999	34 °C	39 %RH	937 hPa
1791458342	34 °C	37 %RH	936 hPa
1791456685	36 °C	33 %RH	936 hPa
1791455028	36 °C	33 %RH	935 hPa
1791453371	36 °C	32 %RH	935 hPa
1791451714	37 °C	32 %RH	935 hPa
1791450057	37 °C	30 %RH	935 hPa
1791448400	38 °C	28 %RH	935 hPa
1791446743	39 °C	26 %RH	935 hPa
1791445086	40 °C	25 %RH	935 hPa
1791443429	41 °C	24 %RH	935 hPa
1791441772	41 °C	22 %RH	935 hPa
1791440115	41 °C	24 %RH	936 hPa
1791438457	40 °C	25 %RH	936 hPa
1791436801	39 °C	27 %RH	937 hPa
1791435143	39 °C	26 %RH	938 hPa
1791433486	39 °C	25 %RH	938 hPa
1791431829	40 °C	25 %RH	939 hPa
1791430172	39 °C	26 %RH	939 hPa
1791428515	39 °C	28 %RH	939 hPa
1791426858	37 °C	30 %RH	940 hPa
1791425201	36 °C	32 %RH	940 hPa
1791423544	35 °C	33 %RH	940 hPa
1791421887	34 °C	34 %RH	940 hPa

*Used Equation Coefficients:

Temp.: 0, 1, 0

Humidity: 0, 1, 0

Pressure: 0, 1, 0

AllCount: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)