EA2RCF LoRa APRS MAP Backup

My position About Go to MAIN map Powered by EA2RCF Radioclub Foronda ☰

reset

YC0TBU-6 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YC0TBU-6. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	Satellite*	HDOP*	Value3*	Value4*	Value5*
1783285080	19 Sat	0 DOP	0	0	0
1783284462	16 Sat	0 DOP	0	0	0
1783283843	21 Sat	0 DOP	0	0	0
1783283225	21 Sat	0 DOP	0	0	0
1783282607	18 Sat	0 DOP	0	0	0
1783281370	18 Sat	0 DOP	0	0	0
1783280753	21 Sat	0 DOP	0	0	0
1783280134	20 Sat	0 DOP	0	0	0
1783279516	19 Sat	0 DOP	0	0	0
1783278898	17 Sat	0 DOP	0	0	0
1783278279	16 Sat	0 DOP	0	0	0
1783277662	16 Sat	0 DOP	0	0	0
1783277043	19 Sat	0 DOP	0	0	0
1783276424	18 Sat	0 DOP	0	0	0
1783275806	17 Sat	0 DOP	0	0	0
1783275188	18 Sat	0 DOP	0	0	0
1783274570	18 Sat	0 DOP	0	0	0
1783273951	20 Sat	0 DOP	0	0	0
1783273334	21 Sat	0 DOP	0	0	0
1783272715	21 Sat	0 DOP	0	0	0
1783272223	20 Sat	0 DOP	0	0	0
1783271479	19 Sat	0 DOP	0	0	0
1783270861	21 Sat	0 DOP	0	0	0
1783268387	17 Sat	0 DOP	0	0	0
1783267770	19 Sat	0 DOP	0	0	0

*Used Equation Coefficients:

Satellite: 0, 1, 0

HDOP: 0, 1, 0

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)