This is the latest recevied telemetry packets stored in our database for station/object XE2B-29. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
| Time | Voltage* | Celsius* | Rel_Hum* | Atm_Press* | Value5* |
|---|---|---|---|---|---|
| 1779479492 | 4.19 VDC | 34.2 C | 25.71 % | 0 hPa | 0 |
| 1779479078 | 4.19 VDC | 36.1 C | 25.49 % | 0 hPa | 0 |
| 1779478759 | 4.19 VDC | 35.6 C | 27.88 % | 0 hPa | 0 |
| 1779476910 | 4.19 VDC | 32.4 C | 27.72 % | 0 hPa | 0 |
| 1779476578 | 4.19 VDC | 32.9 C | 28.29 % | 0 hPa | 0 |
| 1779473473 | 4.02 VDC | 32 C | 34.41 % | 0 hPa | 0 |
| 1779469658 | 4.19 VDC | 30.8 C | 29.81 % | 0 hPa | 0 |
| 1779467122 | 4.19 VDC | 27.2 C | 35.52 % | 815.75 hPa | 0 |
| 1779408060 | 4.1 VDC | 31.3 C | 29.82 % | 0 hPa | 0 |
| 1779406495 | 4.08 VDC | 27.9 C | 31.51 % | 0 hPa | 0 |
| 1779406221 | 4.1 VDC | 29.2 C | 30.6 % | 0 hPa | 0 |
| 1779404317 | 4.06 VDC | 26.1 C | 32.95 % | 0 hPa | 0 |
| 1779402533 | 4.08 VDC | 28.1 C | 31.26 % | 0 hPa | 0 |
| 1779402073 | 4.1 VDC | 31 C | 28.98 % | 0 hPa | 0 |
| 1779400628 | 4.17 VDC | 37.2 C | 24.14 % | 0 hPa | 0 |
| 1779399403 | 4.17 VDC | 40.3 C | 26.52 % | 0 hPa | 0 |
*Used Equation Coefficients:
Voltage: 0, 0.01, 0
Celsius: 0, 0.1, -50
Rel_Hum: 0, 0.01, 0
Atm_Press: 0, 0.125, 0
Value5: 0, 1, 0
- The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
- Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value2 + b * value + c. - The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
- The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
- All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
- A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)