This is the latest recevied telemetry packets stored in our database for station/object OK1VIG-15. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
| Time | TX* | RX* | Digi* | V_Bat* | V_Ext* |
|---|---|---|---|---|---|
| 1771583748 | 682 Count | 827 Count | 205 Count | 3.48 VDC | 0.14 VDC |
| 1771580142 | 681 Count | 827 Count | 205 Count | 3.4 VDC | 0.14 VDC |
| 1771576537 | 680 Count | 827 Count | 205 Count | 3.37 VDC | 0.14 VDC |
| 1771572932 | 679 Count | 827 Count | 205 Count | 3.31 VDC | 0.14 VDC |
| 1771527335 | 678 Count | 827 Count | 205 Count | 3.29 VDC | 0.14 VDC |
| 1771523730 | 677 Count | 827 Count | 205 Count | 3.32 VDC | 0.14 VDC |
| 1771520124 | 676 Count | 827 Count | 205 Count | 3.3 VDC | 0.14 VDC |
| 1771516519 | 675 Count | 827 Count | 205 Count | 3.36 VDC | 0.14 VDC |
| 1771516352 | 674 Count | 827 Count | 205 Count | 3.35 VDC | 0.14 VDC |
| 1771515904 | 672 Count | 827 Count | 205 Count | 3.3 VDC | 0.14 VDC |
| 1771515776 | 671 Count | 827 Count | 205 Count | 3.33 VDC | 0.14 VDC |
| 1771513774 | 670 Count | 827 Count | 205 Count | 3.34 VDC | 0.14 VDC |
| 1771513245 | 669 Count | 827 Count | 205 Count | 3.36 VDC | 0.14 VDC |
| 1771507610 | 664 Count | 827 Count | 205 Count | 3.42 VDC | 0.14 VDC |
*Used Equation Coefficients:
TX: 0, 1, 0
RX: 0, 1, 0
Digi: 0, 1, 0
V_Bat: 0, 0.01, 0
V_Ext: 0, 0.02, 0
- The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
- Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value2 + b * value + c. - The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
- The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
- All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
- A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)