This is the latest recevied telemetry packets stored in our database for station/object BI9BCQ-4. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
| Time | Voltage* | Value2* | Value3* | Value4* | Value5* |
|---|---|---|---|---|---|
| 1771559823 | 3.96 VDC | 0 | 0 | 0 | 0 |
| 1771559760 | 3.96 VDC | 0 | 0 | 0 | 0 |
| 1771557956 | 3.97 VDC | 0 | 0 | 0 | 0 |
| 1771557802 | 3.98 VDC | 0 | 0 | 0 | 0 |
| 1771556789 | 5.61 VDC | 0 | 0 | 0 | 0 |
| 1771502282 | 3.1 VDC | 0 | 0 | 0 | 0 |
| 1771502210 | 3.09 VDC | 0 | 0 | 0 | 0 |
| 1771501942 | 3.24 VDC | 0 | 0 | 0 | 0 |
| 1771501894 | 3.25 VDC | 0 | 0 | 0 | 0 |
| 1771501871 | 3.25 VDC | 0 | 0 | 0 | 0 |
| 1771501435 | 3.31 VDC | 0 | 0 | 0 | 0 |
| 1771501320 | 3.32 VDC | 0 | 0 | 0 | 0 |
| 1771501210 | 3.33 VDC | 0 | 0 | 0 | 0 |
| 1771501188 | 3.33 VDC | 0 | 0 | 0 | 0 |
| 1771500372 | 3.39 VDC | 0 | 0 | 0 | 0 |
| 1771500303 | 3.4 VDC | 0 | 0 | 0 | 0 |
| 1771500281 | 3.4 VDC | 0 | 0 | 0 | 0 |
| 1771500004 | 5.08 VDC | 0 | 0 | 0 | 0 |
| 1771497745 | 5.17 VDC | 0 | 0 | 0 | 0 |
| 1771497722 | 5.17 VDC | 0 | 0 | 0 | 0 |
| 1771497699 | 5.17 VDC | 0 | 0 | 0 | 0 |
| 1771497676 | 5.16 VDC | 0 | 0 | 0 | 0 |
| 1771497642 | 5.16 VDC | 0 | 0 | 0 | 0 |
*Used Equation Coefficients:
Voltage: 0, 0.01, 0
Value2: 0, 1, 0
Value3: 0, 1, 0
Value4: 0, 1, 0
Value5: 0, 1, 0
- The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
- Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value2 + b * value + c. - The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
- The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
- All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
- A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)