This is the latest recevied telemetry packets stored in our database for station/object MB7UIA. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
| Time | V_Batt* | Value2* | Value3* | Value4* | Value5* |
|---|---|---|---|---|---|
| 1779395757 | 4.13 VDC | 0 | 0 | 0 | 0 |
| 1779392158 | 4.13 VDC | 0 | 0 | 0 | 0 |
| 1779388559 | 4.14 VDC | 0 | 0 | 0 | 0 |
| 1779384961 | 4.15 VDC | 0 | 0 | 0 | 0 |
| 1779381362 | 4.15 VDC | 0 | 0 | 0 | 0 |
| 1779377764 | 4.14 VDC | 0 | 0 | 0 | 0 |
| 1779374165 | 4.14 VDC | 0 | 0 | 0 | 0 |
| 1779370566 | 4.15 VDC | 0 | 0 | 0 | 0 |
| 1779366967 | 4.14 VDC | 0 | 0 | 0 | 0 |
| 1779359769 | 4.14 VDC | 0 | 0 | 0 | 0 |
| 1779352553 | 4.15 VDC | 0 | 0 | 0 | 0 |
| 1779349095 | 4.13 VDC | 0 | 0 | 0 | 0 |
| 1779345497 | 4.13 VDC | 0 | 0 | 0 | 0 |
| 1779341899 | 4.13 VDC | 0 | 0 | 0 | 0 |
| 1779338300 | 4.11 VDC | 0 | 0 | 0 | 0 |
| 1779334700 | 4.12 VDC | 0 | 0 | 0 | 0 |
| 1779331101 | 4.12 VDC | 0 | 0 | 0 | 0 |
| 1779327502 | 4.12 VDC | 0 | 0 | 0 | 0 |
| 1779323904 | 4.12 VDC | 0 | 0 | 0 | 0 |
| 1779320305 | 4.13 VDC | 0 | 0 | 0 | 0 |
| 1779316706 | 4.12 VDC | 0 | 0 | 0 | 0 |
| 1779313106 | 4.13 VDC | 0 | 0 | 0 | 0 |
*Used Equation Coefficients:
V_Batt: 0, 0.01, 0
Value2: 0, 1, 0
Value3: 0, 1, 0
Value4: 0, 1, 0
Value5: 0, 1, 0
- The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
- Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value2 + b * value + c. - The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
- The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
- All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
- A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)