EA2RCF LoRa APRS MAP Backup

My position About Go to MAIN map Powered by EA2RCF Radioclub Foronda ☰

reset

F1ZDB-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object F1ZDB-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	V_Batt*	RX*	Relay*	Drop*
1787552846	4.28 VDC	34 pkt	12 pkt	22 pkt
1787551946	4.29 VDC	35 pkt	15 pkt	20 pkt
1787551046	4.29 VDC	35 pkt	17 pkt	18 pkt
1787550145	4.29 VDC	32 pkt	14 pkt	18 pkt
1787549244	4.29 VDC	34 pkt	16 pkt	18 pkt
1787548344	4.3 VDC	33 pkt	13 pkt	20 pkt
1787547444	4.29 VDC	34 pkt	17 pkt	17 pkt
1787546544	4.29 VDC	29 pkt	15 pkt	14 pkt
1787545643	4.29 VDC	35 pkt	14 pkt	21 pkt
1787544743	4.29 VDC	34 pkt	16 pkt	18 pkt
1787543843	4.29 VDC	36 pkt	19 pkt	17 pkt
1787542943	4.29 VDC	37 pkt	19 pkt	18 pkt
1787542043	4.3 VDC	41 pkt	14 pkt	27 pkt
1787541142	4.29 VDC	47 pkt	20 pkt	27 pkt
1787540242	4.3 VDC	29 pkt	11 pkt	18 pkt
1787539341	4.3 VDC	0 pkt	0 pkt	0 pkt
1787538446	4.29 VDC	34 pkt	13 pkt	21 pkt
1787537546	4.3 VDC	36 pkt	18 pkt	18 pkt
1787536645	4.29 VDC	40 pkt	14 pkt	26 pkt
1787535745	4.29 VDC	34 pkt	17 pkt	17 pkt
1787534845	4.29 VDC	32 pkt	15 pkt	17 pkt
1787533945	4.29 VDC	30 pkt	18 pkt	12 pkt
1787533045	4.3 VDC	35 pkt	17 pkt	18 pkt
1787532144	4.28 VDC	34 pkt	15 pkt	19 pkt
1787531244	4.3 VDC	37 pkt	14 pkt	23 pkt

*Used Equation Coefficients:

V_Batt: 0, 0.01, 0

RX: 0, 1, 0

Relay: 0, 1, 0

Drop: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)